அறிமுகம்
This manual provides essential information for the safe and effective installation, operation, and maintenance of your TEMPCO Finned Strip Heater. Please read all instructions carefully before use to ensure proper function and to prevent injury or damage.
முக்கியமான பாதுகாப்பு தகவல்
WARNING: Risk of electric shock and burns. Always disconnect power before installation or servicing. Heating elements can reach extremely high temperatures.
- Ensure all electrical connections are made by a qualified electrician and comply with local and national electrical codes.
- Do not operate the heater in the presence of flammable liquids or gases.
- மின்சார அதிர்ச்சியைத் தடுக்க சரியான தரையை உறுதிப்படுத்தவும்.
- Avoid direct contact with the heater surface during operation and for a significant period after shutdown, as temperatures can remain high.
- ஹீட்டரை திரவத்தில் மூழ்கடிக்க வேண்டாம்.
- வழங்கல் தொகுதி என்பதை சரிபார்க்கவும்tage matches the heater's rated voltage (240VAC).
தயாரிப்பு முடிந்துவிட்டதுview
The TEMPCO Finned Strip Heater is designed for efficient heat transfer in various industrial applications. It features a seamless 304 stainless steel sheath and nickel-plated steel construction, with fins to maximize surface area for heat dissipation. Mounting tabs are included for surface installation.
Image: The TEMPCO Finned Strip Heater, showcasing its finned design and mounting tabs with terminal screws at each end.
அமைவு மற்றும் நிறுவல்
- பேக்கிங் மற்றும் ஆய்வு: Carefully remove the heater from its packaging. Inspect for any signs of shipping damage. Do not install if damage is apparent.
- மவுண்டிங் இடம்: Select a suitable surface mount location that can withstand the heater's operating temperature (up to 1200°F sheath temperature) and provides adequate clearance for air circulation.
- மவுண்டிங்: Secure the heater using the integrated mounting tabs. The tabs feature slotted holes (1/2 inch length, 5/16 inch width) designed for 10-32 screws. Ensure the heater is firmly attached to prevent vibration or movement during operation.
- மின் இணைப்புகள்: Connect the 240VAC power supply to the terminals located at each end of the heater. Ensure all wiring is rated for the heater's voltage and current requirements (350 Watts at 240VAC). Follow all applicable electrical codes.
- அடிப்படை: Properly ground the heater as required by electrical safety standards.
இயக்க வழிமுறைகள்
Once properly installed and wired, the TEMPCO Finned Strip Heater is ready for operation.
- பவர் ஆன்: Apply 240VAC power to the heater circuit. The heater will begin to generate heat immediately.
- வெப்பநிலை கட்டுப்பாடு: For applications requiring precise temperature regulation, it is recommended to integrate an external temperature controller (not included) with appropriate sensing capabilities.
- கண்காணிப்பு: Periodically monitor the heater and surrounding area during initial operation to ensure stable performance and absence of unusual odors or sounds.
- பவர் ஆஃப்: To cease operation, disconnect the 240VAC power supply from the heater circuit.
பராமரிப்பு
Regular maintenance helps ensure the longevity and efficient operation of your finned strip heater.
- மின் துண்டிப்பு: Always disconnect power to the heater and allow it to cool completely before performing any maintenance.
- சுத்தம்: Periodically inspect the fins for dust, debris, or foreign material accumulation. Clean gently with a soft brush or compressed air to maintain optimal heat transfer efficiency. Do not use liquids for cleaning.
- மின் இணைப்புகள்: Annually inspect electrical connections for tightness and signs of corrosion or wear. Tighten any loose connections.
- உடல் பரிசோதனை: Check the heater sheath and mounting tabs for any physical damage, cracks, or deformation. Replace the heater if significant damage is observed.
சரிசெய்தல்
This section addresses common issues you might encounter with your finned strip heater.
| பிரச்சனை | சாத்தியமான காரணம் | தீர்வு |
|---|---|---|
| ஹீட்டர் வெப்பமடையாது | No power supply; Incorrect wiring; Faulty heater element | Check power source and circuit breaker. Verify wiring connections. If power is present and wiring is correct, the element may be faulty and require replacement. |
| போதுமான வெப்பமாக்கல் | தவறான தொகுதிtage; Excessive dirt/debris on fins; Heater undersized for application | Confirm 240VAC supply. Clean fins thoroughly. Ensure the heater's wattage is appropriate for the required heat output. |
| அதிக வெப்பம் | Improper air circulation; Faulty temperature control (if applicable) | Ensure adequate airflow around the heater. Inspect and test any external temperature control devices. |
தொழில்நுட்ப விவரக்குறிப்புகள்
| விவரக்குறிப்பு | விவரம் |
|---|---|
| ஹீட்டர் வகை | Finned Strip Heater |
| ஹீட்டர் தொகுதிtage | 240VAC |
| மொத்த நீளம் | 10-1/2 அங்குலம் |
| பெருகிவரும் பரிமாணம் | 9-1/2 அங்குலம் |
| வாட்ஸ் | 350 வாட்ஸ் |
| Watt Density | 18W/sq. in. |
| டெர்மினல்கள் | Each End |
| Element Width | 1-1/2 அங்குலம் |
| உறை பொருள் | Seamless 304 Stainless Steel |
| பொருள் | Nickel Plated Steel |
| கட்டம் | 1 கட்டம் |
| H x W Across Fins | 1-3/8 x 2 அங்குலம் |
| Max. Sheath Temp. | 1200 டிகிரி F |
| மவுண்டிங் வகை | மேற்பரப்பு மவுண்ட் |
| Slotted Hole Length | 1/2 அங்குலம் |
| Slotted Hole Width | 5/16 அங்குலம் |
| திருகு அளவு | 10-32 |
| தரநிலைகள் | UL அங்கீகரிக்கப்பட்டது |
உத்தரவாதம் மற்றும் ஆதரவு
This TEMPCO Finned Strip Heater is manufactured by Tempco Electric Heater Corp. For specific warranty information or technical support, please contact the manufacturer directly. Keep your purchase receipt for warranty claims.
