அறிவுறுத்தல் கையேடு

அறிமுகம்

This manual provides essential information for the proper installation, operation, and maintenance of the SIMPLEX 4010-9818 Wired Network Media Card. Please read these instructions thoroughly before proceeding with any installation or handling procedures to ensure safe and correct usage.

Figure 1: SIMPLEX 4010-9818 Wired Network Media Card as packaged, including the anti-static bag, ferrite bead kit, and the installation instruction sheet.

பாதுகாப்பு தகவல்

இந்த வழிமுறைகளைப் படித்து சேமிக்கவும்.

This section outlines critical safety precautions and regulatory information. Adherence to these guidelines is mandatory to prevent damage to the product, ensure personal safety, and maintain compliance.

• தயாரிப்பு ஒருமைப்பாடு: Do not install any SIMPLEX product that appears damaged. If damage is apparent, immediately file a claim with the shipping carrier and notify your local SIMPLEX product supplier.
• மின் ஆபத்து: Disconnect electrical field power when making adjustments or repairs to avoid electric shock. Only qualified personnel should perform these tasks.
• Static Hazard: Static electricity can damage sensitive electronic components. Handle the product as follows:
  • Ground yourself before opening or installing the product.
  • Keep the product in its static-shielded bag until it is ready for installation.
  

  Figure 2: The product is enclosed in a static-shielded bag, indicated by the "ATTENTION Static Sensitive" label. Handle with care to prevent electrostatic discharge damage.

• Eye Safety Hazard: Under certain fiber optic application conditions, the optical output of this device may exceed eye safety limits. Do not use magnifying optical devices (e.g., microscopes or other viewing equipment) when viewஇந்த சாதனத்தின் வெளியீடு.
• FCC Rules and Regulations - Part 15: இந்த உபகரணங்கள் சோதனை செய்யப்பட்டு, FCC விதிகளின் பகுதி 15 க்கு இணங்க, வகுப்பு A டிஜிட்டல் சாதனத்திற்கான வரம்புகளுக்கு இணங்குவதாக கண்டறியப்பட்டது. இந்த வரம்புகள் வணிகச் சூழலில் உபகரணங்களை இயக்கும்போது தீங்கு விளைவிக்கும் குறுக்கீட்டிற்கு எதிராக நியாயமான பாதுகாப்பை வழங்க வடிவமைக்கப்பட்டுள்ளன.

அமைவு மற்றும் நிறுவல்

The SIMPLEX 4010-9818 Wired Network Media Card is designed for internal installation within compatible systems. Follow these steps carefully for proper setup.

1. பேக்கிங் மற்றும் ஆய்வு

Carefully remove the network media card from its packaging. Inspect the card for any visible signs of damage. Ensure all components, including the ferrite bead installation kit, are present.

Figure 3: The product is typically shipped in a protective cardboard box, labeled with the product description "WIRED NETWORK MEDIA CARD" and part number 0742100.

Figure 4: The ferrite bead installation kit, part number 9006-073 REV L, is included for proper electromagnetic interference suppression.

2 நிறுவலுக்கான தயாரிப்பு

1. Ensure the host system (Desktop or Laptop) is powered off and disconnected from all power sources.
2. Open the computer case to access the internal component slots.
3. As per safety guidelines, ground yourself to dissipate any static electricity before handling the card.

3. Card Installation

1. Carefully remove the SIMPLEX 4010-9818 card from its static-shielded bag.
2. Align the card with an available compatible internal slot (e.g., PCI, PCIe, depending on the card's interface).
3. Gently but firmly press the card into the slot until it is fully seated. Do not force the card.
4. Secure the card with any retaining clips or screws provided by your computer case.

Figure 5: The reverse side of the anti-static bag confirms the product as a "WIRED MEDIA MODULE," model number 4010-9818.

4. Ferrite Bead Installation (if applicable)

Refer to the specific instructions provided with the ferrite bead kit for proper installation. Ferrite beads are typically installed on cables to reduce electromagnetic interference.

Figure 6: A small plastic bag containing additional components, possibly related to installation or specific configurations, labeled "574-041 Rev. B."

5. Closing the System

Once the card is securely installed, close the computer case and reconnect all peripherals and power cables.

இயக்க வழிமுறைகள்

After successful installation, the SIMPLEX 4010-9818 Wired Network Media Card will function as an integral part of your system's network capabilities.

1. பவர் ஆன்: Power on your computer system. The operating system should detect the new hardware.
2. இயக்கி நிறுவல்: In most modern operating systems, drivers for standard network cards are automatically installed. If prompted, follow the on-screen instructions for driver installation. If automatic installation fails, refer to your system's documentation or the SIMPLEX support website for specific driver downloads.
3. பிணைய இணைப்பு: Connect an Ethernet cable to the network port on the SIMPLEX 4010-9818 card and to your network router or switch.
4. கட்டமைப்பு: Configure network settings (IP address, DNS, etc.) through your operating system's network settings interface as required by your network environment.

பராமரிப்பு

The SIMPLEX 4010-9818 Wired Network Media Card is designed for long-term, reliable operation with minimal maintenance. However, periodic checks can help ensure optimal performance.

• தூசி அகற்றுதல்: Periodically, when the system is powered off and unplugged, open the computer case and gently remove any accumulated dust from the card and surrounding components using compressed air or a soft brush. Dust buildup can impede airflow and lead to overheating.
• கேபிள் இணைப்புகள்: Ensure all network cable connections to the card are secure and free from damage.
• இயக்கி புதுப்பிப்புகள்: While not frequently required, occasionally check the SIMPLEX support website for updated drivers that may offer performance improvements or bug fixes.

சரிசெய்தல்

If you encounter issues with your SIMPLEX 4010-9818 Wired Network Media Card, consider the following common troubleshooting steps:

• நெட்வொர்க் இணைப்பு இல்லை:
  • Verify that the Ethernet cable is securely connected to both the card and the network device (router/switch).
  • Check the network status lights on the card and the network device. Refer to your network device's manual for light indications.
  • Restart your computer and network equipment.
  • Ensure network drivers are correctly installed and updated in your operating system's Device Manager.
• மெதுவான நெட்வொர்க் வேகம்:
  • உங்கள் நெட்வொர்க்கில் அலைவரிசையை பயன்படுத்தும் பிற சாதனங்களைச் சரிபார்க்கவும்.
  • Ensure your Ethernet cable is not damaged and is rated for the appropriate speed (e.g., Cat5e or Cat6 for Gigabit Ethernet).
  • Update network card drivers.
• அட்டை கண்டறியப்படவில்லை:
  • Ensure the card is fully seated in its slot. Power off the system, open the case, and re-seat the card.
  • Check your system's BIOS/UEFI settings to ensure the PCI/PCIe slot is enabled.
  • Test the card in a different compatible slot if available.

If issues persist after attempting these steps, contact SIMPLEX customer support for further assistance.

விவரக்குறிப்புகள்

Key technical specifications for the SIMPLEX 4010-9818 Wired Network Media Card:

உத்தரவாதம் மற்றும் ஆதரவு

For warranty information, technical support, or any inquiries regarding your SIMPLEX 4010-9818 Wired Network Media Card, please contact SIMPLEX customer service.

SIMPLEX is committed to providing dedicated customer service to assist with any questions regarding their products and orders.

Please refer to the official SIMPLEX website or your purchase documentation for the most current contact information and detailed warranty terms.