ஆரிஜின் எஃபெக்ட்ஸ் BASSRIG சூப்பர் வின்tagஇ பாஸ் ப்ரீamp Effects Pedal BR-SV Instruction Manual

அறிமுகம்

The Origin Effects BASSRIG Super Vintage is a bass preamp effects pedal designed to emulate the sound and feel of a classic vintagஇ பாஸ் amplifier. It features an all-analogue signal path and cabinet simulator, providing a wide range of tones from clean to overdriven. This manual provides detailed instructions for setting up, operating, and maintaining your BASSRIG Super Vintage pedal.

தயாரிப்பு முடிந்துவிட்டதுview

படம்: முன் பலகம் view of the Origin Effects BASSRIG Super Vintage pedal. The pedal features a blue lower section and a silver upper section with various control knobs, switches, and input/output jacks. The main footswitch is located at the bottom center.

அமைவு

சக்தி தேவைகள்

BASSRIG சூப்பர் வின்tage requires a 9VDC power supply with a minimum current rating of 20mA. Use a standard 2.1mm center-negative barrel connector. Ensure the power supply meets these specifications to prevent damage to the unit.

இணைப்புகள்

• INSTR (Input): Connect your bass guitar or other instrument to this 1/4" mono input jack.
• AMP வெளியே (வெளியீடு): Connect this 1/4" mono output jack to your bass ampலிஃபையரின் உள்ளீடு.
• DI OUT (Balanced Output): This XLR output provides a balanced signal for direct connection to a mixing console, audio interface, or PA system. It includes an analogue cabinet simulator.
• 9VDC: Power input for the pedal.

Signal Chain Placement

For optimal performance, place the BASSRIG Super Vintage early in your signal chain, typically after any compression pedals and before time-based effects (e.g., delay, reverb) if you are using the AMP OUT to an amplifier. When using the DI OUT, it can serve as the primary tone-shaping device before your recording or live sound system.

இயக்க கட்டுப்பாடுகள்

குமிழ்

• வெளியீடு: Controls the overall output level of the pedal.
• பாஸ்: குறைந்த அதிர்வெண் பதிலை சரிசெய்கிறது.
• மிட்ரேஞ்ச்: Controls the mid-frequency response. This knob works in conjunction with the MIDRANGE FREQUENCY மாறு.
• மரம்: உயர் அதிர்வெண் பதிலை சரிசெய்கிறது.
• கலவை: Mixes the overdriven signal with your clean signal. Fully counter-clockwise is 100% clean, fully clockwise is 100% overdriven.
• இயக்கி: Controls the amount of gain and overdrive applied to the signal.

மாறுகிறது

• MIDRANGE FREQUENCY (220/800/3K): A three-position toggle switch that selects the center frequency for the MIDRANGE knob (220Hz, 800Hz, or 3kHz).
• LO CUT (ULTRA HI): A two-position toggle switch. In the "LO CUT" position, it reduces low frequencies. In the "ULTRA HI" position, it boosts high frequencies.
• DI CAB SIM (FX/FX+BYP): A two-position toggle switch for the DI output.
  • FX: The DI output includes the full effect and cabinet simulation.
  • FX+BYP: The DI output includes the effect with cabinet simulation, but also allows a blend of the bypassed signal.
• AMP OUT EQ (LF/HORN CUT/HF): A three-position toggle switch that applies specific EQ curves to the AMP வெளியே
  • LF: Low-frequency adjustment.
  • HORN CUT (4K/O/2K): A three-position switch within the AMP OUT EQ section, likely for cutting specific high-mid frequencies (4kHz, off, 2kHz) to tame harshness, especially when connecting to an amp with a horn.
  • HF: High-frequency adjustment.
• DI GROUND (LIFT/GND): A two-position toggle switch for the DI output.
  • லிஃப்ட்: Lifts the ground connection to help eliminate ground loops and hum.
  • ஜிஎன்டி: Connects the ground.

ஃபுட்ஸ்விட்ச்

The main footswitch engages or bypasses the effect. It features buffered bypass with silent switching.

பராமரிப்பு

To ensure the longevity and optimal performance of your BASSRIG Super Vintage pedal, follow these maintenance guidelines:

• சுத்தம்: Use a soft, dry cloth to clean the pedal's exterior. Avoid abrasive cleaners or solvents, as they may damage the finish.
• சேமிப்பு: நேரடி சூரிய ஒளி மற்றும் தீவிர வெப்பநிலையிலிருந்து விலகி குளிர்ந்த, உலர்ந்த இடத்தில் பெடலை சேமிக்கவும்.
• பாதுகாப்பு: When transporting, use a padded case to protect the pedal from physical damage.
• சக்தி: பெடல் நீண்ட நேரம் பயன்பாட்டில் இல்லாதபோது எப்போதும் மின்சார விநியோகத்தைத் துண்டிக்கவும்.

சரிசெய்தல்

If you encounter issues with your BASSRIG Super Vintage pedal, refer to the following common troubleshooting steps:

• ஒலி இல்லை:
  • Check all cable connections (instrument, amplifier, power).
  • மின்சாரம் சரியாக இணைக்கப்பட்டுள்ளதா என்பதையும், சரியான மின்னழுத்தத்தை வழங்குவதையும் உறுதிசெய்யவும்.tage (9VDC) and polarity (center-negative).
  • Verify that the pedal is engaged (footswitch LED illuminated).
  • Test with different cables and a different amplifier or instrument to isolate the problem.
• தேவையற்ற சத்தம்/ஹம்:
  • அனைத்து கேபிள்களும் சரியாகப் பாதுகாக்கப்பட்டு நல்ல நிலையில் இருப்பதை உறுதிசெய்யவும்.
  • Try engaging the DI GROUND LIFT switch if using the DI OUT.
  • Test the pedal in isolation from other effects to identify if another pedal is causing the noise.
  • Ensure your power supply is regulated and free from noise.
• Incorrect Tone:
  • Review the settings of all knobs and switches (OUTPUT, BASS, MIDRANGE, TREBLE, BLEND, DRIVE, DI CAB SIM, AMP OUT EQ, LO CUT).
  • உறுதி செய்யவும் கலப்பு knob is not set to 100% clean if you expect an overdriven sound.
  • Consider the placement of the pedal in your signal chain relative to other effects.

இந்தப் படிகள் சிக்கலைத் தீர்க்கவில்லை என்றால், வாடிக்கையாளர் ஆதரவைத் தொடர்பு கொள்ளவும்.

விவரக்குறிப்புகள்

உத்தரவாத தகவல்

Origin Effects products are manufactured to high standards and are typically covered by a limited warranty against defects in materials and workmanship. Please refer to the official Origin Effects website or your purchase documentation for specific warranty terms and conditions applicable to your region and product. Keep your proof of purchase for warranty claims.

ஆதரவு

For further assistance, technical support, or service inquiries regarding your BASSRIG Super Vintage pedal, please visit the official Origin Effects website or contact their customer support team. You can usually find contact information and FAQs on their support pages.