UFO CC10 Multi Function Led Driver User Guide

This guide contains important safety information and installation instructions.
Please read fully before installing, operating or performing any maintenance on the product.

Introduction & Safety

நன்றி, நன்றி.asing the UFO CC10 LED driver. This user guide contains important information and should be read fully before any installation work commences. Please keep for future reference. The CC10 is a compact 350mA, 500mA, 700mA and 1000mA output constant current multi-function driver designed to drive UFO constant current LED fittings up to 50W. Constant voltage LEDs cannot be connected to this driver. Please refer to the specific section within this manual for wiring and connection guidance.

முக்கியமானது
This product must be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product, its component parts and the hazards involved. Electrical wiring and connection must be carried out by a suitably qualified person observing all local and statutory electrical regulations. The CC10 driver is suitable for use only with a class 2 power unit.

முக்கியமான பாதுகாப்பு தகவல்
This driver is designed to work with constant current LED fittings operating on a 350mA, 500mA, 700mA or 1000mA output. Connecting this driver to any other LED devices may result in catastrophic failure of the LED device and/or the CC10 driver. Always check the input current and voltage of the LED devices to ensure compatibility prior to powering up the system. Never hot swap LED fittings. When adding or removing LED fittings always power down the system first. This driver is designed to work on a DC input voltage of 12-48V ONLY. The DC PSU supplying this driver must have an output capability sufficient to power up the driver and maintain the output load. The CC10 driver is suitable for indoor/dry areas and must not be installed in damp அல்லது ஈரமான நிலைமைகள்.

வெளியீட்டு திறன்

The UFO Unidrive CC10 driver supplies a constant current of 350mA, 500mA, 700mA or 1000mA at output voltages between 3.2 and 48V. UFO fittings operate on a max. voltage of 3.2V DC and provide a 1.1W output. The UFO Unidrive CC10 driver has a low voltage DC input. Therefore the PSU used to supply the CC10 is selected based upon the total number of fittings the CC10 will be driving.

LED இன் எண்ணிக்கை பொருத்துதல்கள்	Max Volts DC	Total Watts DC (350mA)	Total Watts DC (500mA)	Total Watts DC (700mA)	Total Watts DC (1000mA)	Standard UFO PSU Paired with an IEC cable for either UK, EU or USA
1	3.6	3.6	4.2	5.1	6.3	702070 12V 5A 60W PSU
2	7.2	4.6	5.6	7.2	9.4	702070 12V 5A 60W PSU
3	10.8	5.5	6.9	9.2	9.5	702070 12V 5A 60W PSU
4	14.4	9.4	11.5	14.8	19.0	700994 24V 3.75A 90W PSU
5	18.0	10.4	13.0	16.9	22.0	700994 24V 3.75A 90W PSU
6	21.6	14.0	17.1	21.9	27.9	700485 36V 1.66A PSU
7	25.2	14.9	18.4	24.0	30.9	700485 36V 1.66A PSU
8	28.8	15.9	19.8	26.0	33.9	700485 36V 1.66A PSU
9	32.4	19.6	24.3	31.4	40.5	700485 36V 1.66A PSU
10	36.0	20.7	25.7	33.6	43.5	700485 36V 1.66A PSU
11	39.6	21.6	26.9	35.5	46.3	708120 48V 0.5A 25W PSU
12	43.2	22.6	28.3	37.5	49.2	708120 48V 0.5A 25W PSU

முக்கியமானது

Connecting too many constant current LED fittings to the CC10 driver with excessive maximum voltage output or using an underrated PSU will result in the driver shutting down. Always check the maximum output voltage of the fittings and ensure that based on 3.6V per LED an adequate number of fittings are connected, and a suitable rated input PSU for the CC10 driver is selected, prior to powering up the system.

செயல்பாட்டுத் தகவல்

Driver PCB Layout

Refer to the table below for description of each part.

சாதனம்	செயல்பாடு
A	Power input jack socket (2.5mm centre positive). DC input voltage 12V to 48V dependent on number of LED fittings connected
B	DMX input/output screw terminals. Data positive, data negative and ground. Occupies two DMX channels – Channel 1 – LED dimming, Channel 2 LED ON/OFF. Use for DMX control or Primary/Secondary link to other CC10 drivers
C	Function LED – indicates signal and control presence
D	Power and fault LED – indicates power input and overcurrent, short circuit and over temperature faults (flashing)
E	Function DIP switch – sets different functions (manual, DMX, sensor input etc.) and also addressing for DMX. Switch down for ON up for OFF
F	0-10V input screw terminals. Positive and negative current source (external receiving voltage) 0-10V dimming voltage input (0 to 100%)
G	Manual (current sink) dimming screw terminals – 10V on screw terminals adjusted by external electronic potentiometer. Normally linked out when not in use
H	Constant current screw terminal output LED + and common ground
J	Set Current. 350mA, 500mA, 700mA or 1000mA. Fit one link only
K	FADE IN potentiometer. Adjusts the fade in time for sensor operation between 1 and 12 seconds
L	DELAY potentiometer. Adjusts the on time for sensor operation (between fade in and fade out) from 1 sec to approximately 5 minutes
M	FADE OUT potentiometer. Adjusts the fade out time for sensor operation be- tween 1 and 12 seconds
N	Sensor input – one normally open (N/O – goes open circuit to trigger FADE IN) one normally closed (N/C – goes closed circuit to trigger FADE IN)

வழக்கமான வயரிங் இணைப்புகள்

முக்கியமானது

Connect ALL LEDs, electrical control and output wiring connections for the complete system BEFORE setting up the driver and connecting the driver PSU to the mains supply.
Never hot swap LED fittings. When adding or removing LED fittings always power down the system first.

இயக்கி அமைப்பு

ALWAYS carry out ALL wiring connections, set current (350mA, 500mA, 700mA or 1000mA) and set up the appropriate functionality (see below) prior to connecting power to the driver.

Non Dimming Operation
For non dimming operation, all of the manual and remote controls are disabled.

Manual Dimming Operation – Current Sink
For manual dimming using an electronic potentiometer, the current sink screw terminal link must first be removed – and a potentiometer connected, in its place. Only compatible electronic potentiometers recommended by UFO are to be used.

0-10V Dimming – Current Source
0-10V dimming (current source) requires an external varying 0 to 10V DC control voltagஇ. கட்டுப்பாட்டு தொகுதிtage will dim both LED outputs simultaneously. See 0-10V value table on following pages. For remote dimming using 0-10V, the current sink screw terminal link must first be inserted.

DMX Dimming & Control

குறிப்பு:
The CC10 driver occupies two DMX channels – see DMX Channel Table.
For guidance on DMX address switch settings see DMX Address Table.

முதன்மை கட்டுப்பாடு

இரண்டாம் நிலை கட்டுப்பாடு

சென்சார் உள்ளீடு

Sensor input may either be Normally Open (N/O) or Normally Closed operation. For N/O operation the sensor must go open circuit to operate the driver. For N/C operation the sensor must go closed circuit to operate the driver.
The sensor circuit has three timers FADE IN, DELAY & FADE OUT. These timers are adjusted by trimmer potentiometers (K, L & M), see sensor table on opposite page.

குறிப்பு:
Where a movement sensor is used to trigger the input, the DELAY and FADE OUT timers will not run to completion until all movement has ceased.

Information Tables

DMX சேனல் அட்டவணை

சேனல் எண்.	செயல்பாடு	மதிப்பு
01	LED Output Dimming	0-255 – No light to maximum light output
02	LED Output On	0-250
02	LED Output Off	251-255

0-10V Current Source Value Table

Value -DC Volts	விளக்கம்
0 - 0.47	LED Output Off
0.48	LED Output Minimum Illumination
10	LED Output Maximum Illumination

சென்சார் அட்டவணை

டிரிம்மர்	வரம்பு (தோராயமாக)	விளக்கம்
ஃபேட் இன்	1 - 10 வினாடிகள்	On sensor operation, fades in LED output from no light to maximum light
தாமதம்	1 - 300 வினாடிகள்	Maintains LED output at maximum light
ஃபேட் அவுட்	1 - 10 வினாடிகள்	After delay, timer fades out LED output from maximum light to no light

குறிப்பு:
The trimmer potentiometers are set for minimum (seconds) at full counter clockwise rotation, maximum seconds) at full clockwise rotation.

DMX Address Tables

Dip Switches S6 to S9

டிஐபி சுவிட்ச் அமைப்பு 0=ஆஃப் 1=ஆன்					S9	0	0	0	0	0	0	0	0	1	1	1	1	1	1	1	1
					S8	0	0	0	0	1	1	1	1	0	0	0	0	1	1	1	1
					S7	0	0	1	1	0	0	1	1	0	0	1	1	0	0	1	1
					S6	0	1	0	1	0	1	0	1	0	1	0	1	0	1	0	1
S1	S2	S3	S4	S5
0	0	0	0	0		0	32	64	96	128	160	192	224	256	288	320	352	384	416	448	480
1	0	0	0	0		1	33	65	97	129	161	193	225	257	289	321	353	385	417	449	481
0	1	0	0	0		2	34	66	98	130	162	194	226	258	290	322	354	386	418	450	482
1	1	0	0	0		3	35	67	99	131	163	195	227	259	291	323	355	387	419	451	483
0	0	1	0	0		4	36	68	100	132	164	196	228	260	292	324	356	388	420	452	484
1	0	1	0	0		5	37	69	101	133	165	197	229	261	293	325	357	389	421	453	485
0	1	1	0	0		6	38	70	102	134	166	198	230	262	294	326	358	390	422	454	486
1	1	1	0	0		7	39	71	103	135	167	199	231	263	295	327	359	391	423	455	487
0	0	0	1	0		8	40	72	104	136	168	200	232	264	296	328	360	392	424	456	488
1	0	0	1	0		9	41	73	105	137	169	201	233	265	297	329	361	393	425	457	489
0	1	0	1	0		10	42	74	106	138	170	202	234	266	298	330	362	394	426	458	490
1	1	0	1	0		11	43	75	107	139	171	203	235	267	299	331	363	395	427	459	491
0	0	1	1	0		12	44	76	108	140	172	204	236	268	300	332	364	396	428	460	492
1	0	1	1	0		13	45	77	109	141	173	205	237	269	301	333	365	397	429	461	493
0	1	1	1	0		14	46	78	110	142	174	206	238	270	302	334	366	398	430	462	494
1	1	1	1	0		15	47	79	111	143	175	207	239	271	303	335	367	399	431	463	495
0	0	0	0	1		16	48	80	112	144	176	208	240	272	304	336	368	400	432	464	496
1	0	0	0	1		17	49	81	113	145	177	209	241	273	305	337	369	401	433	465	497
0	1	0	0	1		18	50	82	114	146	178	210	242	274	306	338	370	402	434	466	498
1	1	0	0	1		19	51	83	115	147	179	211	243	275	307	339	371	403	435	467	499
0	0	1	0	1		20	52	84	116	148	180	212	244	276	308	340	372	404	436	468	500
1	0	1	0	1		21	53	85	11	149	181	213	245	277	309	341	373	405	437	469	501
0	1	1	0	1		22	54	86	118	150	182	214	246	278	310	342	374	406	438	470	502
1	1	1	0	1		23	55	87	119	151	183	215	247	279	311	343	375	407	439	471	503
0	0	0	1	1		24	56	88	120	152	184	216	248	280	312	344	376	408	440	472	504
1	0	0	1	1		25	57	89	121	153	185	217	249	281	313	345	377	409	441	473	505
0	1	0	1	1		26	58	90	122	154	186	218	250	282	314	346	378	410	442	474	506
1	1	0	1	1		27	59	91	123	155	187	219	251	283	315	347	379	411	443	475	507
0	0	1	1	1		28	60	92	124	156	188	220	252	284	316	348	380	412	444	476	508
1	0	1	1	1		29	61	93	125	157	189	221	253	285	317	349	381	413	445	477	509
0	1	1	1	1		30	62	94	126	158	190	222	254	286	318	350	382	414	446	478	510
1	1	1	1	1		31	63	95	127	159	191	223	255	287	319	351	383	415	447	479	511

Switches S1 to S5 / DMX Address

சரிசெய்தல்

பிரச்சனை	சாத்தியமான காரணங்கள்	பரிகாரம்
	மெயின் சப்ளை நிறுத்தப்பட்டது	விநியோகத்தை சரிபார்த்து மீண்டும் நிறுவவும்
[பொது] System is dead – power LED (D) not lit. No light output from LED	தளர்வான மெயின் பிளக்குகள்	பிளக்குகளை சரிபார்க்கவும்
	Loose DC output wire or connection	அனைத்து இணைப்புகளையும் சரிபார்க்கவும்
	PSU failed – check output	பொதுத்துறை நிறுவனத்தை மாற்றவும்
	with DVM
	Driver PCB failure	இயக்கி மாற்றவும்
[பொது] One output channel is dead Power LED (D) is lit	Loose output wire to dead channel or faulty/poorly fitting power in on extrusion. Check output with DVM	அனைத்து இணைப்புகளையும் சரிபார்க்கவும்
[பொது] One output channel is dead Power LED (D) is lit	Driver PCB failure	இயக்கி மாற்றவும்

[NO DIMMING MODE] System is dead – power LED (D) lit.	Current sink input link in place – DIP switch 10 on	Switch 10 off or remove link
[NO DIMMING MODE] System is dead – power LED (D) lit.	Loose output GND wire or poorly fitting power in on extrusion	அனைத்து இணைப்புகளையும் சரிபார்க்கவும்
ஒளி வெளியீடு இல்லை	PSU failed – check output with DVM	பொதுத்துறை நிறுவனத்தை மாற்றவும்
	Driver PCB failure	இயக்கி மாற்றவும்

[MANUAL DIMMING MODE]

Power LED (D) lit – function LED

Switch 10 off Switch 10 to on

Electronic potentiometers Check polarity of

wired incorrectly – wrong connections and reconnect

polarity correctly.

[0-10V DIMMING MODE] Power LED (D) lit – function LED (C) not lit. Output LED devices illuminated but not dimming	Switch 10 is off	Switch 10 to on
[0-10V DIMMING MODE] Power LED (D) lit – function LED (C) not lit. Output LED devices not illuminated	0-10V wired incorrectly – wrong polarity	Check polarity of connections and reconnect correctly
	0-10V control signal missing check input with DVM	Check all connections and output of 0-10v controller using DVM
[0-10V DIMMING MODE] Power LED (D) lit – function LED (C) lit. Output LED devices illuminated but flickering	0V from 0-10V control signal is missing	Check all connections and output of 0-10V controller using DVM

பிரச்சனை	சாத்தியமான காரணங்கள்	பரிகாரம்
[DMX DIMMING MODE] Power LED (D) lit – function LED (C) lit. Output LED devices illuminated but not responding to DMX	DMX address not set on DIP switches 1-9	DMX முகவரியை அமைக்கவும்
[DMX DIMMING MODE] Power LED (D) lit – function LED (C) lit. Output LED devices not illuminated and not responding to DMX	Switch 10 is on	Switch 10 off
	Incorrect DMX address set	Set correct DMX address
[DMX DIMMING MODE] Power LED (D) lit – function LED (C) not lit. Output LED devices illuminated but not responding to DMX	DMX control signal missing	Check all connections are secure and correct polarity and confirm output of DMX controller and/or previous DMX device in DMX chain

[SECONDARY MODE] Power LED (D) lit – function LED (C) not lit. Output LED devices illuminated but not responding to master control	Primary driver not set up correctly	Check primary driver set up
	DMX control signal from primary driver missing	Check all connections are secure and correct polarity and confirm output of primary driver and/or previous devices in primary / secondary DMX chain

[N/O or N/C SENSOR OPERATION] Power LED (D) lit – function LED (C) not lit. Output LED devices illuminated but not responding to sensor	Switch 10 is off	Switch 10 to on
[N/O SENSOR OPERATION] Power LED (D) lit – function LED (C) not lit. Output LED devices not illuminated and not responding to sensor	Switch 1 is off	Switch 1 to on
	Current sink input link in place	இணைப்பை அகற்று
[N/C SENSOR OPERATION] Power LED (D) lit – function LED (C) not lit. Output LED devices not illuminated and not responding to sensor	Switch 2 is off	Switch 2 to on
	Current sink input link in place	இணைப்பை அகற்று
[N/O or N/C SENSOR OPERATION] Power LED (D) lit – function LED (C) not lit. Output LED devices not illuminated and not responding to sensor	Sensor control signal is missing	Check all connections and output of sensor using DVM
	Sensor wired to wrong input	Check input connections and rewire

பிரச்சனை	சாத்தியமான காரணங்கள்	பரிகாரம்
[SHORT CIRCUIT] Output LED devices go out and power LED (D) flashes rapidly	Short circuit between LED output and GND. Short circuit between LED1 output and/or LED 2 output and GND	Check for short circuit on output cables using a DVM. Repair or replace faulty cables or devices.

[OVER CURRENT]

Heavily loaded system – Output LED devices go out momentarily and power LED (D) flashes rapidly

System overloaded beyond 30W

Reduce load by removing some LED fittings until a safe working load of not more than 30W is achieved

[OVER TEMPERATURE]

Output LED devices go out momentarily and power LED (D) flashes rapidly

Driver ambient temperature too hot

Relocate driver to cooler ambient environment

தொழில்நுட்ப தகவல்

தயாரிப்பு குறியீடு	DR-CC-DC-48-50-D-CU (driver with single integral dimming potentiometer) DR-CC-DC-48-50-ALL-CU (driver with fully functional manual / dmx / 0-10V / sensor control)
விளக்கம்	50W fully functional dimmable constant current driver
உள்ளீட்டு சக்தி	12-48 வி டி.சி.
மதிப்பிடப்பட்ட சக்தி	50W அதிகபட்ச வெளியீடு
வெளியீடு மின்னோட்டம்	350mA, 500mA, 700mA, 1000mA
இணைப்பு	Power – 2.1mm input jack plug Control & Outputs – screw terminals
பாதுகாப்பு	SCP / OCP / OTP
செயல்பாடு	Individual manual (current sink) dimming with electronic potentiometer 0-10V (current source) output dimming DMX with 2 channels (LED dimming & on/off). Controllable from DMX system or can operate standalone master/slave with other CC10 drivers. 2 channels (N/O & N/C) sensor input to trigger output LED devices with fade in, delay and fade out controls.
சுற்றுப்புற தற்காலிக.	Min. -20°C to Max. +45°C
ஐபி மதிப்பீடு	IP20 உட்புற பயன்பாட்டிற்கு மட்டுமே
பரிமாணங்கள்	180mm (7.09") x 116.5mm (4.59") x 44.5mm (1.75")

தொடர்பு கொள்ளவும்

Universal Fibre Optics
Home Place
Coldstream, TD12 4DT
ஐக்கிய இராச்சியம்
+44 (0) 1890 883416
www.ufo.lighting

Universal Fiber Optics USA

1749 Northgate Blvd
Sarasota, FL34238
அமெரிக்கா
941-343-8115
www.fiberopticlighting.com

UFO Licht GmbH

Andreastraße 20
93059 ரெஜென்ஸ்பர்க்
Deutschland
+49 (0) 9491 955880
www.ufo-licht.de

அடிக்கடி கேட்கப்படும் கேள்விகள்

Q: What happens if I connect too many LED fittings or use an underrated PSU with the CC10 driver?

A: The driver may shut down to prevent damage. Always ensure the total number of fittings and the PSU rating are appropriate before powering up the system.

ஆவணங்கள் / ஆதாரங்கள்

UFO CC10 Multi Function Led Driver [pdf] பயனர் வழிகாட்டி
CC10 Multi Function Led Driver, CC10, Multi Function Led Driver, Multi Function Led Driver, Function Led Driver, Led Driver, Driver

குறிப்புகள்

பயனர் கையேடு

UFO CC10 Multi Function Led Driver

விவரக்குறிப்புகள்